Antenna
Antenna	Internal integrated
Antenna Qty	2
Directivity	Omni-directional
Environmental Parameters
Humidity Range Operating	10 - 95% (non-condensing)
Max Operating Temperature	122 °F
Min Operating Temperature	32 °F
Expansion / Connectivity
Interfaces	1 x network / power - Ethernet 10Base-T/100Base-TX/1000Base-T - RJ-45
General
Data Link Protocol	IEEE 802.11b IEEE 802.11a IEEE 802.11g IEEE 802.11n
Device Type	Wireless access point
Dimensions (WxDxH)	7.1 in x 2.4 in x 7.1 in
Enclosure Type	External - indoor
Features	Power over Ethernet (PoE) Wireless Intrusion Detection System (WIDS) Wi-Fi Multimedia (WMM) support SpectraLink Voice Priority (SVP) support Quality of Service (QoS) 2T2R MIMO technology Maximum Ratio Combining (MRC) Direct Sequence Spread Spectrum (DSSS) Cyclic Delay Diversity (CDD) Space Time Blocking Code (STBC)
Frequency Band	2.4 GHz 5 GHz
Localization	United States
Power Over Ethernet (PoE) Supported	PoE
Miscellaneous
Compliant Standards	ICES-003 Class B FCC Part 15 B IC MIC R&TTE RoHS IEC 60950-1 WEEE EN 301.893 EN 60601-1-2 CSA C22.2 No. 60950-1
Networking
Compliant Standards	IEEE 802.3u IEEE 802.3i IEEE 802.3ab IEEE 802.11b IEEE 802.11a IEEE 802.3af IEEE 802.11g IEEE 802.1x IEEE 802.11i IEEE 802.11e IEEE 802.11n IEEE 802.3at IEEE 802.3az
Connectivity Technology	Wireless
Data Link Protocol	IEEE 802.11b IEEE 802.11a IEEE 802.11g IEEE 802.11n
Data Transfer Rate	300 Mbps
Encryption Algorithm	TKIP WPA WPA2 AES-CCMP
Features	Power over Ethernet (PoE) Wireless Intrusion Detection System (WIDS) Wi-Fi Multimedia (WMM) support SpectraLink Voice Priority (SVP) support Quality of Service (QoS) 2T2R MIMO technology Maximum Ratio Combining (MRC) Direct Sequence Spread Spectrum (DSSS) Cyclic Delay Diversity (CDD) Space Time Blocking Code (STBC)
Form Factor	External
Frequency Band	2.4 GHz 5 GHz
Spread Spectrum Method	OFDM DSSS
Power
Power Consumption Operational	11 Watt
Power Over Ethernet (PoE) Supported	PoE
Processor / Memory / Storage
Hard Drive	None.

Juniper Networks AP with dual radios 802

Juniper Networks AP with dual radios 802.11a/b/g/n 2x2 MIMO (2SS), single 1000Base-T 802.3af PoE Ethernet port, 4 internal antennas. Not rated for plenum use. Ceiling/Wall mount bracket included. Required for operation in USA. The WLA522-US is a quality system with 802.11a/b/g/n wireless protocols and 2x2 MIMO (2SS) technology based dual radios. The Wi-Fi bands are 2.4 GHz and 5 GHz. The system is integrated with a Power over Ethernet (PoE) port. There are a full four internal antennas within this Juniper WLA Wireless Access Point, and the directivity of the antenna is omni-directional. The Maximum Ratio Combining (MRC), Direct Sequence Spread Spectrum (DSSS), and the Cyclic Delay Diversity (CDD) further highlight the advanced technological design of this access point. Support is offered with Wi-Fi Multimedia (WMM) and SpectraLink Voice Priority (SVP). The interface of the WLA522-US is an Ethernet 10Base-T/100Base-TX/1000Base-T. The connector type of the interface is RJ-45. The spread spectrum method is DSSS and OFDM, and the data transfer rate is 300 Mbps. Power Consumption Operational is listed at 11 Watts. The high-end Wireless Intrusion Detection System (WIDS) ensures the safety and the security of the system is well maintained. A Space Time Blocking Code (STBC) is integrated within the device. This is a new PC compatible Juniper Wireless Access Point. A Ceiling/Wall mount bracket is included with a purchase and this ensures the mount will be compatible with the actual device.